Paint for interior industrial floors, of the highest quality.
15(7.5+7.5l.) l
4(2+2l.) l
C. TECHNIQUES
Colors
C. APPLICATION
Suitable for concrete floors, cement mortars and other derivatives. Suitable for interior surfaces, garages, workshops, warehouses, industrial buildings, factories, car parks.
Adherent finishes.
Great covering power.
Filling power.
High hardness and balanced elasticity.
Ease of application.
Resistant to abrasion, scrubbing, wear, grease spills, mineral oils, other chemical agents and dirt in general.
Dilution.9971
T. Drying3-4hours
T. Repainted8-24hours
Performance7-10m2/L
Pot life6-8 h.
Semi bright
semi-glossy chrome green
semi-bright english red
grey 7038 semi-gloss
Surface preparation
Surfaces should be sanded, clean, dry, free of dust, grease, oils and moisture. Clean, dry and well-set soil (28 days). Residual soil moisture: Less than 6% Preferably with roughness to improve adhesion. On unpainted surfaces: Apply 3 layers. First hand diluting (maximum 10%) with FAST DRYING SYNTHETIC DILUENT (Ref. 9971), second and third hand to use or slightly diluted (maximum 5%). On surfaces with old paint: Remove paint in poor condition and proceed as on unpainted surfaces. On surfaces with old paint in good condition: Sand and clean the surface and apply two hands to use or slightly diluted (maximum 5%). For difficult supports (aged chlororubber paints, PVC, plastics, ceramic supports, etc.): Use the WHITE MATTE WATER EPOXY PRIMER (Ref. J6744) with MATTE WATER EPOXY PRIMER CATALYST (Ref. K0864) (See technical sheet) or consult the Technical Department.
Before applying
Application temperature: Higher than 8ºC. Support temperature: Above 5ºC. Ambient relative humidity: Less than 75%. Residual soil moisture to be applied: Less than 6%
How to use
Remove the contents of the container well. Prepare the amount to use. Mix component A with component B: 1 parts component A with 1 part component B (by weight). It is supplied in two packages: Component A and Component B. The packaging of Component A is not provided filled in order to incorporate the entire contents of Component B. Shake until fully incorporated (mixing machine). Let stand 9-10 minutes. Apply with good air renewal, in thin, uniform and well-extended layers. Percentage of application, Brush and Roller: Fast Drying Synthetic Thinner (Ref. 9971) 1st hand diluted (5 – 10%), 2nd and 3rd hand to use or slightly diluted (maximum 5%)
Storage
Store in a cool place. Do not store open or started containers.
Calculate how much you need:
Total area
m2
nth Layers
Necessary amount--
Suitable for concrete floors, cement mortars and other derivatives. Suitable for interior surfaces, garages, workshops, warehouses, industrial buildings, factories, car parks.
Surfaces should be sanded, clean, dry, free of dust, grease, oils and moisture. Clean, dry and well-set soil (28 days). Residual soil moisture: Less than 6% Preferably with roughness to improve adhesion. On unpainted surfaces: Apply 3 layers. First hand diluting (maximum 10%) with FAST DRYING SYNTHETIC DILUENT (Ref. 9971), second and third hand to use or slightly diluted (maximum 5%). On surfaces with old paint: Remove paint in poor condition and proceed as on unpainted surfaces. On surfaces with old paint in good condition: Sand and clean the surface and apply two hands to use or slightly diluted (maximum 5%). For difficult supports (aged chlororubber paints, PVC, plastics, ceramic supports, etc.): Use the WHITE MATTE WATER EPOXY PRIMER (Ref. J6744) with MATTE WATER EPOXY PRIMER CATALYST (Ref. K0864) (See technical sheet) or consult the Technical Department.
Before applying
Application temperature: Higher than 8ºC. Support temperature: Above 5ºC. Ambient relative humidity: Less than 75%. Residual soil moisture to be applied: Less than 6%
How to use
Remove the contents of the container well. Prepare the amount to use. Mix component A with component B: 1 parts component A with 1 part component B (by weight). It is supplied in two packages: Component A and Component B. The packaging of Component A is not provided filled in order to incorporate the entire contents of Component B. Shake until fully incorporated (mixing machine). Let stand 9-10 minutes. Apply with good air renewal, in thin, uniform and well-extended layers. Percentage of application, Brush and Roller: Fast Drying Synthetic Thinner (Ref. 9971) 1st hand diluted (5 – 10%), 2nd and 3rd hand to use or slightly diluted (maximum 5%)
Storage
Store in a cool place. Do not store open or started containers.
PINTURAPOLIURETANOSUELOSINTERIOR
Data sheet
Family
Floor paint
Surface
Cement
Concrete
Feature Listed 1
ADHERENT FINISHES.
Feature listed 2
GREAT COVERING POWER.
Subname
Paint for interior industrial floors, of the highest quality.
Feature listed 3
FILLING POWER.
Barpicolor
No
Featured product 1
Adherent finishes.
Featured product 2
Great covering power.
Featured product 3
Filling power.
Featured product 4
High hardness and balanced elasticity.
Featured product 5
Ease of application.
Featured product 6
Resistant to abrasion, scrubbing, wear, grease spills, mineral oils, other chemical agents and dirt in general.
i-dilution
.9971
i-t.drying
3-4hours
Product Featured 7
Eliminates the formation of dust on the soil, improves its surface hardness, prevents erosion and wear facilitating its cleaning by providing a decorative finish
Suitable for concrete floors, cement mortars and other derivatives. Suitable for interior surfaces, garages, workshops, warehouses, industrial buildings, factories, car parks.
