Paint for industrial floors, exterior and of the highest quality.
16(12+4l.) l
4(3+1l.) l
C. TECHNIQUES
Colors
C. APPLICATION
Suitable for concrete floors, cement mortars and other derivatives. Suitable for exterior and interior surfaces, garages, workshops, warehouses, industrial buildings, factories, car parks.
Excellent resistance
Great covering power.
High hardness and good elasticity.
Fill power and ease of application.
Adherent finishes.
Resistant to abrasion, scrubbing, wear, grease spills, mineral oils, other chemical agents and dirt in general.
DilutionA9708
T. Drying3-4hours
T. Repainted12-24hours
Performance7-10m2/L
Pot life10-12 h.
Semi bright
semi-glossy white
grey 7038 semi-gloss
semi-bright english red
semi-glossy chrome green
Surface preparation
Surfaces should be sanded, clean, dry, free of dust, grease, oils and moisture. Clean, dry and well-set soil (28 days). Preferably with roughness to improve adhesion. On unpainted surfaces: Apply 2 or 3 layers. First hand diluting (maximum 15%) with DILUENT POLYURETHANES EXTERIOR FLOORS (Ref. A9708), second and third hand to use or slightly diluted (maximum 5%). On surfaces with old paint: Remove paint in poor condition and proceed as on unpainted surfaces. For difficult supports (aged chlororubber paints, PVC, plastics, ceramic supports, etc.): Use the WHITE MATTE WATER EPOXY PRIMER (Ref. J6744) with MATTE WATER EPOXY PRIMER CATALYST (Ref. K0864) (See technical sheet) or consult the Technical Department.
Before applying
Application temperature: Higher than 8ºC. Support temperature: Above 5ºC. Ambient relative humidity: Less than 75%. Residual soil moisture to be applied: Less than 6%
How to use
Remove the contents of the container well. Prepare the amount to use. Mix component A with component B: 3 parts component A with 1 part component B (in volume) or 4 parts component A with 1 part component B (by weight). Shake until fully incorporated (mixing machine). Let stand 9-10 minutes. Apply with good air renewal, in thin, uniform and well-extended layers. Percentage of application, Brush and Roller: DILUENT POLYURETHANES EXTERIOR FLOORS (Ref. A9708), 1st hand diluted (maximum 15%), 2nd and 3rd hand to use or slightly diluted (maximum 5%)
Storage
Store in a cool place. Do not store open or started containers.
Calculate how much you need:
Total area
m2
nth Layers
Necessary amount--
Suitable for concrete floors, cement mortars and other derivatives. Suitable for exterior and interior surfaces, garages, workshops, warehouses, industrial buildings, factories, car parks.
Surfaces should be sanded, clean, dry, free of dust, grease, oils and moisture. Clean, dry and well-set soil (28 days). Preferably with roughness to improve adhesion. On unpainted surfaces: Apply 2 or 3 layers. First hand diluting (maximum 15%) with DILUENT POLYURETHANES EXTERIOR FLOORS (Ref. A9708), second and third hand to use or slightly diluted (maximum 5%). On surfaces with old paint: Remove paint in poor condition and proceed as on unpainted surfaces. For difficult supports (aged chlororubber paints, PVC, plastics, ceramic supports, etc.): Use the WHITE MATTE WATER EPOXY PRIMER (Ref. J6744) with MATTE WATER EPOXY PRIMER CATALYST (Ref. K0864) (See technical sheet) or consult the Technical Department.
Before applying
Application temperature: Higher than 8ºC. Support temperature: Above 5ºC. Ambient relative humidity: Less than 75%. Residual soil moisture to be applied: Less than 6%
How to use
Remove the contents of the container well. Prepare the amount to use. Mix component A with component B: 3 parts component A with 1 part component B (in volume) or 4 parts component A with 1 part component B (by weight). Shake until fully incorporated (mixing machine). Let stand 9-10 minutes. Apply with good air renewal, in thin, uniform and well-extended layers. Percentage of application, Brush and Roller: DILUENT POLYURETHANES EXTERIOR FLOORS (Ref. A9708), 1st hand diluted (maximum 15%), 2nd and 3rd hand to use or slightly diluted (maximum 5%)
Storage
Store in a cool place. Do not store open or started containers.
PINTURAPOLIURETANOSUELOSEXTERIOR
Data sheet
Family
Floor paint
Surface
Cement
Concrete
Feature Listed 1
EXCELLENT RESISTANCE
Feature listed 2
GREAT COVERING POWER.
Subname
Paint for industrial floors, exterior and of the highest quality.
Feature listed 3
HIGH HARDNESS AND GOOD ELASTICITY.
Barpicolor
No
Featured product 1
Excellent resistance
Featured product 2
Great covering power.
Featured product 3
High hardness and good elasticity.
Featured product 4
Fill power and ease of application.
Featured product 5
Adherent finishes.
Featured product 6
Resistant to abrasion, scrubbing, wear, grease spills, mineral oils, other chemical agents and dirt in general.
i-dilution
A9708
i-t.drying
3-4hours
Product Featured 7
It eliminates the formation of dust on the soil, improves its surface hardness, prevents erosion and wear facilitating its cleaning by providing a decorative finish.
Suitable for concrete floors, cement mortars and other derivatives. Suitable for exterior and interior surfaces, garages, workshops, warehouses, industrial buildings, factories, car parks.
