Suitable for waterproofing, protection and decoration of concrete facades, mortars, walls and in general any exterior vertical surface. Especially indicated on surfaces that oscillate or tend to produce fissures or cracks and require high protection to the outside.
Very resistant
Waterproofs and protects
Penetrates into cracks and fissures.
Ease of application.
Applicable with different thicknesses, according to the required needs.
Resistant to the alkalinity of the substrates, to the weather, to the thermal changes and to the small movements of works.
DilutionWater
T. Drying30-60 min.
T. Repainted2-4hours
Performance5-7m2/L
Semi-Matte
semi-matte white
intact 60*
Surface preparation
Surfaces should be clean, dry, free of dust, grease, oils, moisture, chipped and consistent. On new surfaces and cement mortars without saltpeter: apply at least 3 crossed layers: the 1st hand diluted with 5% water, the rest to use or slightly diluted (maximum 5%). Restore cracks and fissures with SAND mixture and cover with fiberglass fabric band. On soft surfaces (mortars in poor condition) or with saltpeters, old plastic paints, lime and other paints: Remove soft, crumbly, chipped and damp parts. Also remove lime and saltpeters. Seal properly with SELLAFOND (Ref .1764) and proceed as in the previous case.
Before applying
Application temperature: Above 5ºC. Ambient relative humidity: Less than 80%. Support temperature above 8ºC.
How to use
Remove the contents of the container well. Apply in uniform layers. Apply with good air renewal. Application to brush, roller and airless gun. Do not apply if there is a risk of rain and frost. It is not convenient to apply in full sun and with high temperatures of the support.
Storage
Store in a cool place. Do not store open or started containers.
Calculate how much you need:
Total area
m2
nth Layers
Necessary amount--
Suitable for waterproofing, protection and decoration of concrete facades, mortars, walls and in general any exterior vertical surface. Especially indicated on surfaces that oscillate or tend to produce fissures or cracks and require high protection to the outside.
Surfaces should be clean, dry, free of dust, grease, oils, moisture, chipped and consistent. On new surfaces and cement mortars without saltpeter: apply at least 3 crossed layers: the 1st hand diluted with 5% water, the rest to use or slightly diluted (maximum 5%). Restore cracks and fissures with SAND mixture and cover with fiberglass fabric band. On soft surfaces (mortars in poor condition) or with saltpeters, old plastic paints, lime and other paints: Remove soft, crumbly, chipped and damp parts. Also remove lime and saltpeters. Seal properly with SELLAFOND (Ref .1764) and proceed as in the previous case.
Before applying
Application temperature: Above 5ºC. Ambient relative humidity: Less than 80%. Support temperature above 8ºC.
How to use
Remove the contents of the container well. Apply in uniform layers. Apply with good air renewal. Application to brush, roller and airless gun. Do not apply if there is a risk of rain and frost. It is not convenient to apply in full sun and with high temperatures of the support.
Storage
Store in a cool place. Do not store open or started containers.
Colores A Carta-4
Data sheet
Family
Facade cladding
Surface
Cement
Concrete
Facades
Feature Listed 1
VERY RESENTFUL
Feature listed 2
WATERPROOFS AND PROTECTS
Subname
High quality waterproofing elastic coating.
Feature listed 3
PENETRATES INTO CRACKS AND FISSURES.
Barpicolor
Sí
Featured product 1
Very resistant
Featured product 2
Waterproofs and protects
Featured product 3
Penetrates into cracks and fissures.
Featured product 4
Ease of application.
Featured product 5
Applicable with different thicknesses, according to the required needs.
Featured product 6
Resistant to the alkalinity of the substrates, to the weather, to the thermal changes and to the small movements of works.
i-dilution
Water
i-t.drying
30-60 min.
Product Featured 7
Resistant to degradation and aging caused by environmental pollution (anticarbonation).